|
| |
Teflon Coated Glass Fabric Tapes
TFES-2HD* · TFES-3 · TFES-5 SELF-WOUND (without Liner) on 3" Plastic Core
Impregnated fiberglass cloth tape with silicone adhesive. Excellent
electrical, mechanical and chemical properties. Used as a primary
insulation in a variety of electrical equipment and heat sealing bars,
chute liners, gaskets, bearing surfaces, tabletop covers, guide rails and
roll covers. Low friction surface; abrasion resistant. Product comes
standard with liner.
Self-wound is optional at no additional cost (specify "no
liner" by adding "SW" to product number, e.g. TFE-6SW).
Teflon™ coated glass fabrics ( without adhesive ) are also available
(specify by adding "NA" to product number, e.g. TFE-5NA). -
Roll Size of "NA": 37-˝" wide x 36 Yd
long (37 - ˝" wide x 18 yd long available at half the price of the
36 yd roll listed below). 1/2 and 3/4 WIDE ROLLS MUST BE SELF WOUND |
| |
| Physical Properties: |
| Operating temperature range: -40F to
500F(-40C to 260C). Elongation: 5% |
| |
|
TFE-3 or TFE -3SW |
TFE-5 or TFE
-5SW |
TFE-6 or TFE
-6SW |
TFE-10 or
TFE -10SW |
| Backing |
3
mil/0.003" |
5
mil/0.005" |
6
mil/0.006" |
10mil/0.010" |
| Total thickness |
0.0045" |
0.0065" |
0.0075" |
0.0120" |
| Break strength (lb/in) |
40 |
80 |
90 |
160 |
| Adhesion (oz/in) |
30 |
35 |
40 |
40 |
| Electrical strength(total
volts) |
3000 |
5000 |
8400 |
6500 |
| Alternative to: 3M |
#5451 |
#5452 |
#5453 |
#5454 |
| DeWal |
#134-3 |
#134-5 |
#134-6 |
#134-10 |
|
CHR |
#A2205 |
#A2007 |
#A2008 |
#A2012 |
| Greenbelt |
#100-3S |
#100-5S |
#100-6S |
#100-10S |
|
|
|
|
Length: 36 YD (108') 33M |
| INCHES |
MM
|
RLS/CS |
| 1/2" |
12.7 |
72 |
| 3/4" |
19.0 |
48 |
| 1" |
25.4 |
36 |
| 1 1/2" |
38.1 |
24 |
| 2" |
50.8 |
18 |
| 3" |
76.2 |
12 |
| 36" |
914.0 |
|
| 37 1/2" |
("NA" no
adhesive) |
|
|
|
|
|
|
|
|
|
|
Skived Teflon (PTFE Film) Tapes
TFE - Mil Thickness ( -3, -5, -6, or -10 ) > > > Specify WITH or WITHOUT LINER < < <
Pure Skived Teflon™ (PTFE film) with a high temp. Silicone Adhesive. Used in electrical applications such as harness / coil wraps & separators, transformers and slot liners where good insulation and heat resistance are required. Also used in mechanical applications such as heat sealing bars & jaws, labeling machine pressure pads, chute liners, anti-friction devices, bearings, forming dies, aircraft mold release & guide rails where high temperature, maximum slip and lubricity are required.
*TFES-2HD is a High Density, TENSILIZED Skived PTFE film which provides higher tensile strength, lower elongation and higher dielectric strength than regular skived film (primarily used for electrical applications listed above & for roll protection in flat die extrusion). High elongation of TFES-3 & TFES-5 permit tight
wrapping; conforms to sharp bends/irregular surfaces.
|
|
| PHYSICAL PPROPERTIES |
TFES-2HD |
TFES-3 |
TFES-5 |
| Backing |
2 mil/0.002" |
3 mil/0.003" |
5mil/0.005" |
| Total thickness |
0.0035" |
0.0045" |
0.0065" |
| Break strength (lb/in) |
30 |
18 |
30 |
| Adhesion (oz/in) |
36 |
36 |
40 |
| Elongation |
100 |
300 |
300 |
| Temperature rating (°F cont. use) |
-100 to +500 |
-100 to +500 |
-100 to +500 |
| Dielectric strength (total volts) |
10,000 |
11,000 |
14,000 |
| Alternative to: 3M |
#5480 |
|
#5481 |
| Permacel |
#P422 |
#P427 |
#P421 |
| DeWal |
#204-2HD |
#204-3 |
#204-5 |
|
|
|
| INCHES |
MM |
RLS/CS |
| 1/4" |
6.4 |
144 |
| 3/8" |
9.5 |
96 |
| 1/2" |
12.7 |
72 |
| 3/4" |
19.0 |
48 |
| 1" |
25.4 |
36 |
| 1 1/2" |
38.1 |
24 |
| 2" |
50.8 |
18 |
| 3" |
76.2 |
12 |
|
|
LOG |
|
|
|
|
|
|
|
|
-30-
| |
|
